Puch Cobra MC 2016 - In Austria
+3
Francis
Jeffward
Rene555
7 participantes
Página 1 de 1.
Re: Puch Cobra MC 2016 - In Austria
Hola!!
En el sonido del motor tienes un problema de carburación. La mezcla que se produce a pocas rpm es excesivamente pobre. La moto necesita mas gasolina abajo.
El tener los transfer de carga tan grandes crea un vacío que pienso es perjudicial para la parte baja de funcionamiento de las revoluciones. La moto se vuelve algo perezoza.
En el sonido del motor tienes un problema de carburación. La mezcla que se produce a pocas rpm es excesivamente pobre. La moto necesita mas gasolina abajo.
El tener los transfer de carga tan grandes crea un vacío que pienso es perjudicial para la parte baja de funcionamiento de las revoluciones. La moto se vuelve algo perezoza.
Jeffward- Usuario Maestro
Re: Puch Cobra MC 2016 - In Austria
Hi
Its my first 6 speed engine that i have so i have to learn about it. I know that the Carb whas wrong it is only a 21mm so i will change it to an 28mm than i set it up for the engine . Next i will paint the Bike and rebuild it a little bit. thanks
Its my first 6 speed engine that i have so i have to learn about it. I know that the Carb whas wrong it is only a 21mm so i will change it to an 28mm than i set it up for the engine . Next i will paint the Bike and rebuild it a little bit. thanks
Rene555- Usuario Nuevo
Re: Puch Cobra MC 2016 - In Austria
Intenta conseguir un carburador de 26mm mejor.
Jeffward- Usuario Maestro
Re: Puch Cobra MC 2016 - In Austria
My first Testride and it was so much fun . This Engine runs very nice now with the 28mm Carb and has a lot of Power.
Rene555- Usuario Nuevo
Re: Puch Cobra MC 2016 - In Austria
Congratulations!!! your motorbike have good sound and a lot of power. I have 28 carbs in my cobra also, and the performance is very good.
We want see the new advances of the paint and esthetic.
Best wishes.
Francis.
We want see the new advances of the paint and esthetic.
Best wishes.
Francis.
Francis- Usuario Maestro
Re: Puch Cobra MC 2016 - In Austria
[size=16] Muchas revoluciones del motor y... como siempre... POCOS METROS! (LOMAT)
Re: Puch Cobra MC 2016 - In Austria
Madre de Dios, esa Puch necesita combustible!!!! lleva muy pobre la mezcla.
Sergio Puch- Usuario Nuevo
Re: Puch Cobra MC 2016 - In Austria
Mas gasolina en la zona baja/media de rpm.
Sube la aguja, cierra el tornillo de aire del carburador, o aumenta el tornillo de bajas. ¡O todas las cosas a la vez!
Sube la aguja, cierra el tornillo de aire del carburador, o aumenta el tornillo de bajas. ¡O todas las cosas a la vez!
Jeffward- Usuario Maestro
Re: Puch Cobra MC 2016 - In Austria
Thanks for the help. I think i have to fix my clutch i think that is the reason that the engine can not run free when i turn the bike in the video . I have now tried ATF oil its a little better but not gone. When i pull the clutch and put in a gear the engine will go off .
Rene555- Usuario Nuevo
Re: Puch Cobra MC 2016 - In Austria
Rene555 escribió:My first Testride and it was so much fun . This Engine runs very nice now with the 28mm Carb and has a lot of Power.
Pero dejala respirar un poco hombre, que la vas a fundir
Blanfer2- Usuario Aprendiz
Re: Puch Cobra MC 2016 - In Austria
what brand of ignition is and where you can get
Joseillo- Usuario Aprendiz
Re: Puch Cobra MC 2016 - In Austria
Its a selfmade prototype .The flywheel is modified and the stator . It also have 2 Curves programmed i can switch between
Rene555- Usuario Nuevo
Temas similares
» Puch Shop Austria
» Puch Condor MD85 - En Austria
» Interesante Página Web De Puch MC 50 Austria
» Visita Al Museo Johann Puch En Graz - Austria
» Puch Cobra MC 75 - Donde Estará Mi Antigua Cobra
» Puch Condor MD85 - En Austria
» Interesante Página Web De Puch MC 50 Austria
» Visita Al Museo Johann Puch En Graz - Austria
» Puch Cobra MC 75 - Donde Estará Mi Antigua Cobra
Página 1 de 1.
Permisos de este foro:
No puedes responder a temas en este foro.
|
|
Hoy a las 20:12 por Julio C G
» Presentación
Dom 5 Mayo 2024 - 20:26 por Julio C G
» Buenos días, me presento
Dom 5 Mayo 2024 - 20:25 por Julio C G
» Presentación desde Asturias
Dom 5 Mayo 2024 - 20:24 por Julio C G
» Presentación
Dom 5 Mayo 2024 - 20:23 por Julio C G
» SALON DE BARCELONA, Motociclismo 608
Dom 5 Mayo 2024 - 20:19 por Julio C G
» Puch minicross super 1 o 2 ?
Dom 5 Mayo 2024 - 19:21 por hugoo
» cobra tt 1ªserie. Nuevo proyecto
Mar 30 Abr 2024 - 9:05 por Motorito
» Nueva restauración de una x20
Vie 26 Abr 2024 - 6:23 por williamsgbd
» Puch M125
Jue 25 Abr 2024 - 16:41 por JandroFR
» Motociclismo 608 - Mayo 1979 - Novedades Puch
Jue 25 Abr 2024 - 16:38 por JandroFR
» COBRA 80 K 1982 Salon Colonia
Dom 21 Abr 2024 - 20:21 por Julio C G
» IFMA 1980 PUCH 80 Agua
Sáb 20 Abr 2024 - 18:34 por Julio C G
» Primera Quedada Puch 2010
Vie 19 Abr 2024 - 20:14 por RayaHuelva
» Puch Condor Trail - Manual De Uso Y Mantenimiento
Jue 18 Abr 2024 - 10:42 por jgajga